Easy Sizing Instructions
Easy Sizing Instructions for sheet fed presses and folders running paper:
- Identify the blower line coming from the pump/compressor going to the feeder. Isolate the line BEFORE it separates into smaller lines going to different parts of the feeder.
- Measure the inside diameter of that main blower hose. When selecting hose fitting, always order a unit with the hose fitting air opening equal to or larger than the ID of the blower hose. If you downsize the hose fitting you run the risk of air restriction in the blower line due to the smaller hose fitting opening.
- Determine the maximum sheet size that can run on the equipment (not the size of paper the customer runs on the equipment). When in doubt of sizing, always order a larger model Ionix Static Eliminator than required. Undersized Ionix units may not completely neutralize the static charges in the paper. Remember: You cannot over neutralize paper.
Use the chart below:
| Maximum Sheet Size | Blower hose inside diamter | Ionix Model# | Price |
|---|---|---|---|
| Up to 11" x 17" (Up to 27cm x 42cm) | 1/4" (7mm) | 100-1 | $99.00 |
| From
11" x 17" To
22" x 34" (From 27cm x 42cm To 55cm x 85cm) |
1/4" (7mm) 1/2" (14mm) 3/4" (20mm) 1" (26mm) 1 1/4” (32mm) |
200-1 200-2 200-3 200-4 200-5 |
$140.00 |
| From
22" x 34" To
26" x 40" (From 55cm x 85cm To 65cm x 100cm) |
1/4" (7mm) 1/2" (14mm) 3/4" (20mm) 1" (26mm) 1 1/4” (32mm) |
300-1 300-2 300-3 300-4 300-5 |
$185.00 |
Sheet Fed Presses
Duplicator Presses: For virtually every 11x17, 12x18 format duplicator press the correct size Ionix unit is Model 100-2).
* Check inside diameter of blower hose before ordering
- AB Dick: 320/325/350/360/367/369 - Model 100-2; 375/385/9800 series - Model 200-2; Century 3000 - Model 200-3
- AM Multigraphics: 1250/1250LW/2650/1330/1360/1650/1850/1860/1960 - Model 100-2; 1218 Model 200-2
- ATF Chief: 15/115/215/17/117/215/Super Chief 2115/2117/2217/XL Series - Model 200-2
- Aurelia - OMSCA: 124/125/225/129/39B/39A - Model 300 *; 40" OMSCA - Model 300-3
- Davidson: 221/241/251/400/500 - Model 100-2; 233/600/700/900 - Model 200-2
- Gestetner:313 - Model 100-2
- Hamada: 500-600-601/602/611/612 - Model 100-2; 700/800 - Model 200-2; RS34 - Model 200-3
- Harris: Please call with press model
- Hashimoto: 26" - Model 200-4
- Heidelberg: GTO/TOK/TOM - Model 100-2; K-Series - Model 200-2; S-Series 300-2; Drupa 40" 2/C - 300-2
- Imperial: 1117/2200/3200/4200 - Model 100-2
- Indigo: E Print 1000 - Model 200-2
- Itek: 950/960/975 - Model 100-2; 3985 Model 200-2
- Kluge: 14 x 22 - Model 200-3
- Komori: 40" - Model 300-4; 26" Please call. Do not install on 26" without consulting Ionix
- Man Roland: 600/700 - Model 300-4
- Merganthaler: 40" - Model 300-4
- Miehle: 17 Litho Print - Model 100-2; 29New/36/38/41 - Model 300-4; Favorite/24/59/29 - Please call.
- Miller: TP29-Model 200 *; TP38/38A/TP41 - Model 300 *
- Rotaprint: R/30 - Model 100-2; RGS/RKL/RGB - Model 100 *
- Royal Zenith: 15S - Model 100 *
- Ryobi: 480/524H/640 - Model 200-2; 524P - Model 200-2; 512 - Model 100-3; 2700/2800/3200/3985 series - Model 200-2; 3302 - Verfiy statis probelm is NOT on feeder board. Please call for proper sizing;
- Omni-Adast: 725 - Model 200-3; 755 - Model 300-3
- Shinohara: 662P/664P - Model 200-3
- Solna: 125/225 - Model 200-2' 129/230/238 - Model 300 *
- Toko: 4700/4750 - Model 200-2
![[Printers Parts Store is your source for new replacement parts, rollers, accessories and supplies for offset and letterpress printing equipment]](images/PPSLogoHigh.png)